Procedure And 3mf File For Drying Filament With The X1 Series Printer While it can’t dry filament, the ams can keep it dry by acting as a dry box. you just need to keep dry desiccant loaded into it. there are two locations under where you place the filament that opens up and you can add desiccant packs into. I have just tried the filament drying utility of the x1c (as i need higher temperatures than my sunlu s1 can provide) and after some hours i checked to see if everything was going ok but i found an error message on the screen that said: “drying failed”.
Procedure And 3mf File For Drying Filament With The X1 Series Printer Filaments can be dried before printing using either a blast (forced air) drying oven, a filament drier or the x1 and p1 series bambu lab printers. this wiki article provides instructions on using the x1 p1 series printer heatbed for filament drying:. To make it more convenient for users to dry filaments, we utilize the following two functions in the printer to create a drying environment: the heating function of the heatbed. the enclosed space of the printer. note: p1p a1 a1 mini are open printers and don't support filament drying. Dry the filament according to the correct operation, temperature, and time. the recommended drying parameters for each type of filament are listed as follows: if you purchased refill filament, please mount the filament onto a spool before drying. Using a filament dryer, i've only ever been able to get it down to about 15% inside the filament dryer. usually <20% is good enough to print for petg, and pla isn't as touchy about moisture. so don't worry as much about over drying it.
How To Dry Filament On The X1 And P1 Series Heatbed Bambu Lab Wiki Dry the filament according to the correct operation, temperature, and time. the recommended drying parameters for each type of filament are listed as follows: if you purchased refill filament, please mount the filament onto a spool before drying. Using a filament dryer, i've only ever been able to get it down to about 15% inside the filament dryer. usually <20% is good enough to print for petg, and pla isn't as touchy about moisture. so don't worry as much about over drying it. To properly dry a filament you need 6 8, sometimes even more hours. that's hours that your printer can't print. as someone without a dehydrator i actually had this same idea before it was a feature!. I see the x1c has a drying option, but i’d like to dry multiple spools (of the same type) at once. is there any special way to do this other than just stacking them? is that even recommended?. Does drying in the x1c work well, or should i not bother trying? the x1c works fine as a dryer, just a little slow. use a filament box with the lid removed as a cover, the printed bambu model does not work any better. if moisture is the problem, drying on the heat bed will prove it. You are allowed to use any filament that is approved by bambu labs as ams safe. the nozzles on the printers are hardened steel 0.4mm which will handle glow in the dark filament. you might need to increase the temp just a bit to get good results.
How To Dry Filament On The X1 And P1 Series Heatbed Bambu Lab Wiki To properly dry a filament you need 6 8, sometimes even more hours. that's hours that your printer can't print. as someone without a dehydrator i actually had this same idea before it was a feature!. I see the x1c has a drying option, but i’d like to dry multiple spools (of the same type) at once. is there any special way to do this other than just stacking them? is that even recommended?. Does drying in the x1c work well, or should i not bother trying? the x1c works fine as a dryer, just a little slow. use a filament box with the lid removed as a cover, the printed bambu model does not work any better. if moisture is the problem, drying on the heat bed will prove it. You are allowed to use any filament that is approved by bambu labs as ams safe. the nozzles on the printers are hardened steel 0.4mm which will handle glow in the dark filament. you might need to increase the temp just a bit to get good results.