Ezcad User Manual How To Set Laser Marking Machine Parameter Speed Users simply need to copy ezcad2 folder that is in the install cd to hard disk, and then double click the ezcad2.exe under the ezcad2‘s directory to run the software. ezcad2 requires a software security device sometimes known as a 'dongle'. this device plugs into the usb port on the pc. Master laser™ master laser.cnphone： 86 18115672211spype：westseasonswhatsapp： 86 18115672211e mail: tom@master laser.cn.
How To Install Driver For Laser Marking Machine Ezcad2 Software First, enter the laser marking machine software ezcad, and deselect the use default param on the right. change the value, such as the default speed is 500, you can adjust it to 1500 or more. however, after adjusting the speed, the marking effect will not be clear enough. Subscribe for more! bit.ly 2topqfd ezcad software is suitable for all brand fiber laser marking machine, now this video to let you learn how to set up your new fiber laser machine. Ezcad software empowers you to control your laser marking machine with precision. but with an array of options, navigating parameter settings can feel overwhelming. this blog cuts through the complexity, guiding you through setting common ezcad parameters to achieve flawless laser marking. Set the calibration parameters click “f1 设置激光器参数” to set the laser type and marking parameters (normally, the marking parameters are default). in general, the fiber laser type is ipg, spi, and is checked separately.
Github Mesviki2896 Ezcad2 Laser Marking Ezcad software empowers you to control your laser marking machine with precision. but with an array of options, navigating parameter settings can feel overwhelming. this blog cuts through the complexity, guiding you through setting common ezcad parameters to achieve flawless laser marking. Set the calibration parameters click “f1 设置激光器参数” to set the laser type and marking parameters (normally, the marking parameters are default). in general, the fiber laser type is ipg, spi, and is checked separately. When the power’s range is changed less then 100% during marking, the time is less proportional to the max vaule. this function is suit for the laser power supply with slow response speed. if the laser power supply ’ s response speed is very quick, this value may be 0 ms. Using this function, the hatch lines and text are marking together. part diameter: click it, and fill in part diameter. focus length: click it and fill in focus length of f θlens. note: the two parameters affect marking result directly. Machine parameter: fly mark 1)enable: enable the fly marking function. 2)enable speed simulation: enable the pipeline speed in hardware simulation mode. 3)pipeline from right to left: check to indicate…. 1)min value: the laser can set the minimum frequency. 2)max value: laser can set the maximum frequency. 3)frequency delay: delay time required when the laser changes frequency. 4)pwm opening delay: time delay of rising edge and rising edge of gate when pwm is on. power map: set the user defined power ratio and the actual power ratio.
Ezcad Software Operation Problems Of Laser Marking Machine Ella Xtlaser When the power’s range is changed less then 100% during marking, the time is less proportional to the max vaule. this function is suit for the laser power supply with slow response speed. if the laser power supply ’ s response speed is very quick, this value may be 0 ms. Using this function, the hatch lines and text are marking together. part diameter: click it, and fill in part diameter. focus length: click it and fill in focus length of f θlens. note: the two parameters affect marking result directly. Machine parameter: fly mark 1)enable: enable the fly marking function. 2)enable speed simulation: enable the pipeline speed in hardware simulation mode. 3)pipeline from right to left: check to indicate…. 1)min value: the laser can set the minimum frequency. 2)max value: laser can set the maximum frequency. 3)frequency delay: delay time required when the laser changes frequency. 4)pwm opening delay: time delay of rising edge and rising edge of gate when pwm is on. power map: set the user defined power ratio and the actual power ratio.