Filament Tangled Or Stuck Bambu Lab Wiki First check whether the filament on the spool is tangled or sunk, and whether the ptfe tube is installed incorrectly or the ams lite is placed too far away from the printer, as shown in solution 1. if not, please manually press the tool head cutter to cut off the filament. 2. Check if the filament is tangled or sagged and stuck, and avoid using filaments that are not supported by ams, such as tpu damp pva. check if the feed funnel of the first stage feeder is seriously worn, if there is wear, please refer to the wiki for replacement. check if the spring of the ams buffer or hub is stuck:.
Filament Tangled Or Stuck Bambu Lab Wiki The bambu a1 series is equipped with a filament tangle detection module to deal with this situation. when the filament is tangled, due to excessive feeding resistance, the corresponding sensor will be triggered, and the printer will automatically pause printing and pop up a reminder of filament entanglement. There seems to be filament stuck leading into the extruder? however there is no filament in the nozzle (pulled it out manually) and i cannot extrude it thru or pull it out? any ideas would be greatly appreciated : ). When you have a tangled spool, the end of the filament will be under another filament loop, like this: to untangle, move the end so that is no longer under the loop. kinda difficult to explain in text, here is a video explaining it:. Hey so i am having a issue with my a1 mini where is starts the print prints for about an hour then cuts the filament a says to check if it is caught or stuck. i have resliced it four times and same problem. i use hatchbox pla and am trying to print one piece in one color. any solutions??.
Filament Tangled Or Stuck Bambu Lab Wiki When you have a tangled spool, the end of the filament will be under another filament loop, like this: to untangle, move the end so that is no longer under the loop. kinda difficult to explain in text, here is a video explaining it:. Hey so i am having a issue with my a1 mini where is starts the print prints for about an hour then cuts the filament a says to check if it is caught or stuck. i have resliced it four times and same problem. i use hatchbox pla and am trying to print one piece in one color. any solutions??. Step 2: check if the filament is tangled or sagged and stuck. please avoid using filaments unsupported by ams, such as tpu damp pva. step 3: c heck if the feed funnel of the first stage feeder is seriously worn. if there is wear, please refer to the wiki for replacement. As long as it's being held whether by your fingers, the ams, or some sort of clip that keeps it secure on the roll during storage it won't get tangled. sometime during the life of the spool, the end of the filament became loose and tied itself up. it is possible but very rare to have tangles present from the manufacturer. I thoroughly dried my filament, but the filament keeps shifting to the outside of the spool and the ams detects it as "stuck" even though very light pressure is required to shift and fix it. works ok for a little bit, then gets itself "stuck" again. i'm using pla and i've had this problem with many different brands and many different types. When that doesn’t work, your 3 steps are a core loop of an ultimately effective way of fixing things. for ours, i figured out that nothing was stuck or jammed. the filament was actually getting rammed into something inside the filament buffer which wasn’t filament. it happens with any filament that is cut off flat, instead of at an angle.
Filament Tangled Or Stuck Bambu Lab Wiki Step 2: check if the filament is tangled or sagged and stuck. please avoid using filaments unsupported by ams, such as tpu damp pva. step 3: c heck if the feed funnel of the first stage feeder is seriously worn. if there is wear, please refer to the wiki for replacement. As long as it's being held whether by your fingers, the ams, or some sort of clip that keeps it secure on the roll during storage it won't get tangled. sometime during the life of the spool, the end of the filament became loose and tied itself up. it is possible but very rare to have tangles present from the manufacturer. I thoroughly dried my filament, but the filament keeps shifting to the outside of the spool and the ams detects it as "stuck" even though very light pressure is required to shift and fix it. works ok for a little bit, then gets itself "stuck" again. i'm using pla and i've had this problem with many different brands and many different types. When that doesn’t work, your 3 steps are a core loop of an ultimately effective way of fixing things. for ours, i figured out that nothing was stuck or jammed. the filament was actually getting rammed into something inside the filament buffer which wasn’t filament. it happens with any filament that is cut off flat, instead of at an angle.
Filament Tangled Or Stuck Bambu Lab Wiki I thoroughly dried my filament, but the filament keeps shifting to the outside of the spool and the ams detects it as "stuck" even though very light pressure is required to shift and fix it. works ok for a little bit, then gets itself "stuck" again. i'm using pla and i've had this problem with many different brands and many different types. When that doesn’t work, your 3 steps are a core loop of an ultimately effective way of fixing things. for ours, i figured out that nothing was stuck or jammed. the filament was actually getting rammed into something inside the filament buffer which wasn’t filament. it happens with any filament that is cut off flat, instead of at an angle.
Filament Tangled Or Stuck Bambu Lab Wiki